Choose a normally closed (NC) reed switch for circuits requiring a single path that opens upon magnetic actuation. Choose a Form C changeover switch when a common terminal must transfer between NC and NO paths. Form C switches can also deliver NC-only operation through the COM–NC terminals.
Non-latching, passive reed contacts require matching contact logic, electrical ratings, and magnetic actuation behavior before testing within a live circuit.
Key Differences Between Normally Closed and Form C Reed Switches
Contact arrangement is the primary distinction. Among reed switches, an SPST-NC device provides a single switched path, whereas a Form C switch provides two paths linked by a common terminal.
Normally Closed Reed Switches
A normally closed reed switch maintains a conductive path in its reference state and opens upon magnetic actuation. This configuration is designated SPST-NC (single pole, single throw, normally closed) or Form B.
Manufacturers implement NC operation using dedicated NC contacts, a Form C device wired only to its NC path, or an internal bias magnet. In biased designs, a permanent magnet holds open-type contacts closed; an opposing external magnetic field neutralizes that bias, allowing the contacts to open. The term “normal” designates the manufacturer’s specified reference state. Biased assemblies maintain an active internal magnetic field even in the absence of an external actuator.
Form C Changeover Reed Switches
A Form C changeover switch provides SPDT (single pole, double throw) operation. The common terminal (COM) connects to the NC contact at rest. Magnetic actuation breaks this path and connects COM to the normally open (NO) terminal.
Form C switches use break-before-make sequencing: COM disconnects from NC before engaging NO, leaving both circuits open during transition. Because both paths share the COM terminal, they cannot function as isolated circuits.
| Comparison Point | Normally Closed Reed Switch | Form C Changeover Reed Switch |
| Contact arrangement | SPST-NC / Form B function | SPDT / Form C |
| Available connections | One NC contact path | COM–NC and COM–NO |
| Reference state | NC path closed | COM–NC closed; COM–NO open |
| Actuated state | NC path open | COM–NC open; COM–NO closed |
| Transfer action | No second exposed path | Break-before-make transfer |
| Typical task | Interrupt one signal path | Select between two signal paths |

Contact form defines circuit topology alone. Operating ratings, physical sensing range, and service life depend on the specific switch construction.
How to Choose the Right Reed Switch for Your Application
Selection starts with circuit switching requirements, followed by load ratings, magnetic operating limits, and mechanical constraints.
Single NC Path
An SPST-NC switch suits circuits requiring a single path that opens upon actuation, such as an input signaling that a mechanism has arrived at a target position. Verify the required circuit state at each actuator position before specifying the part. Selecting an NC device based solely on whether equipment runs closed-circuit during typical operation can result in incorrect logic. A Form C switch can execute the same single-circuit function via its COM and NC terminals, though the unused third terminal adds no functional value unless a future secondary signal path is needed.
Changeover Contacts
Form C switches serve applications routing a common signal between two branches, such as a tank level monitor toggling between separate standby and alarm circuits. The connected system must tolerate the open interval during contact transfer. Circuits requiring continuous conduction cannot rely on standard Form C contacts alone. Circuit designs must also accommodate contact bounce during switching transitions.
Replacement Compatibility
A replacement component must match both circuit switching logic and physical operating conditions. Compare:
- Switching voltage, switching current, and switching power under actual operating loads.
- Continuous carry current across closed contacts.
- Individual ratings for NC and NO paths.
- Magnetic sensitivity, actuation polarity, and pull-in and drop-out positions.
- Package dimensions, lead spacing, and physical mounting constraints.
Continuous carry ratings typically exceed active switching ratings. For details on inrush currents and inductive turn-off spikes, see the reed switch current rating guide. Reject components that fail to meet baseline electrical ratings. Devices that meet electrical criteria but exhibit different magnetic sensitivity require validation in the physical assembly before deployment.
How to Verify Contact States
De-energized continuity testing confirms path conduction across reference and actuated states, though it cannot verify load capacity, operational life, or high-speed switching response.

Step1: Confirm the Specified Reference State
Review the model’s pinout diagram and application notes to determine whether the unit incorporates a bias magnet and confirm that the drawing depicts the unactuated state. Position the operating magnet at its reference location or remove it entirely. Leave any integral bias magnets in place. Removing electrical power does not release contacts held by permanent magnets. The reed switch symbol guide shows how reference states map to standard schematic symbols.
Step2: Identify the Contact Paths
Isolate the switch from surrounding circuitry before testing resistance to prevent parallel paths from distorting readings. Identify terminals using the manufacturer’s pinout. In the reference state, an SPST-NC switch must show continuity across its lead pair. A Form C device must exhibit continuity between COM and NC alongside an open circuit between COM and NO.
When working with components like the XGH Series reed switch, match the complete part number to its specific engineering drawing. Photographs or broad series names do not reliably verify terminal layouts. Resolve any discrepancies between readings and schematics before connecting the switch to a powered circuit.
Step3: Test Magnetic Actuation and Release
Advance the operating magnet along its planned path. Confirm that the NC path opens and, on Form C devices, that COM–NO closes. Withdraw the magnet to verify contact reset. Repeat this check at maximum tolerance gaps and offset alignments. Actuation and release points rarely coincide due to magnetic hysteresis, so record both distances separately.
Magnetic sensitivity is rated in ampere-turns (AT) using standardized test coils. This value does not define a fixed physical sensing distance. The reed switch AT guide details how AT ratings relate to magnet selection. A digital multimeter verifies settled contact states. Inspecting dynamic behavior, such as contact bounce or transfer intervals, requires an oscilloscope and a current-limited test circuit.
Using a Form C Reed Switch as an SPST-NC Replacement
A Form C switch can replace an SPST-NC unit if its COM–NC path reproduces the target switching logic and its ratings meet installation limits. For example, take a position sensor using a passive SPST-NC contact that remains closed at rest and opens when an actuator approaches. A Form C device yields identical settled states through its COM and NC terminals.
Connect the circuit leads to COM and NC. Leave the NO lead unconnected and electrically insulated in accordance with manufacturer guidelines; trimming the lead is unnecessary.
Apply the following compatibility criteria:
- Operating load: Disqualify any switch whose voltage, current, or power ratings fall below circuit demands.
- Magnetic operation: The actuator must trigger and release the switch across all mechanical mounting tolerances without requiring magnet or bracket alterations.
- Circuit performance: If electrical and mechanical parameters align, evaluate the installed switch for false triggers, contact bounce issues, and reliable release.
Bench continuity confirms terminal logic, but qualification requires verified operation under real-world loads and motion profiles.

To review replacement options with XURUI, submit your model and operating details, including schematics, load voltage and current, actuator travel path, and available mounting clearance.
Common Questions About NC and Form C Reed Switches
Does a Closed Door Mean the Reed Switch Is Normally Closed?
No. Mechanical door position does not determine electrical contact classification. In typical setups, closing a door moves an actuator magnet into range of a normally open switch, holding the contacts closed during standby. Contact classification depends on manufacturer documentation and the unactuated state of the switch rather than fixture position.
Can Reversing the Wires Change a Reed Switch from NC to NO?
No. Inverting the leads of a passive reed switch does not alter its contact behavior. On a Form C switch, alternating between NC and NO requires moving the physical wire from the NC terminal to the NO terminal. Sensors containing active electronics or LED indicators may have dedicated polarity requirements and should be wired according to their assembly diagrams.
Is a Normally Closed Reed Switch Automatically Fail-Safe?
No. An NC switch does not provide fail-safe protection on its own. While a monitored closed loop identifies broken wiring, it cannot detect contact welding or parallel shorts that keep the circuit closed during actuation. True fail-safe operation requires supervisory circuitry and controller diagnostics to manage these failure modes.
External Sources
- HSI Sensing — Creating the Form-B Reed Switch
- Reed Sensor Dynamics — Form C Contact Definition
- Standex Detect — Basic Electrical Parameters of Reed Switch Products
- OMRON — Why Is a Safety Relay Required for Safety Circuits?








